System-sensor CR-6 Bedienungsanleitung PDF herunterladen

D500-48-00 1 I56-1798-009

INSTALLATION AND MAINTENANCE INSTRUCTIONS

BEFORE INSTALLING

This information is included as a quick reference installation guide. If the

modules will be installed in an existing operational system, inform the op-

erator and local authority that the system will be temporarily out of service.

Disconnect the power to the control panel before installing the modules. This

system contains static sensitive components. Always ground yourself with a

proper wrist strap before handling any circuits so that static charges are re-

moved from the body. The housing cabinet should be metallic and suitably

grounded.

NOTICE: This manual should be left with the owner/user of this equipment.

GENERAL DESCRIPTION

The CR-6 Six Relay Control Module is intended for use in an intelligent alarm

system. Each module is intended for Form-C switching applications, which do

not require wiring supervision for the load circuit. A single isolated set of dry

relay contacts is provided for each module, which is capable of being wired

for either normally open or normally closed for each operation. Each module

has its own address. A pair of rotary code switches is used to set the address

of the first module from 01 to 94. The remaining modules are automatically as-

signed to the next five higher addresses. Provisions are included for disabling

a maximum of three unused modules to release the addresses to be used else-

where. Each CR-6 module also has panel controlled green LED indicators. The

panel can cause the LEDs to blink, latch on, or latch off.

CR-6 Six Relay Control Module

SPECIFICATIONS

Normal Operating Voltage: 15-32 VDC

Stand-By Current: 1.45 mA

Alarm Current: 32 mA (assumes all six relays have been switched once and all six LEDs solid on)

Temperature Range: 32°F to 120°F (0°C to 49°C)

Humidity: 10 to 93% Non-condensing

Dimensions: 6.8˝H × 5.8˝W × 1.0˝D

Accessories: BB-2 Cabinet; BB-6 Cabinet; CH-6 Chassis

Wire Gauge: 12-18 AWG

Relay Current: 30 mA/Relay Pulse (15.6 mS pulse duration) pulse under panel control

3825 Ohio Avenue, St. Charles, Illinois 60174

1-800-SENSOR2, FAX: 630-377-6495

www.systemsensor.com

CONTENTS INCLUDE:

(6) 1 x 3 Terminal Blocks

(1) 1 x 4 Terminal Blocks

(2) 1¼˝ (32mm) Stand offs

(4) Machine Screws

(1) Shunt (NOTE: For the disable position, not more than one shunt shall be

installed at the same time)

(2) Nuts

COMPATIBILITY REQUIREMENTS

To ensure proper operation, this module shall be connected to a compatible

control panel only.

COMPONENTS

Following are descriptions of the CR-6 mounting frameworks. There are two

mounting options for CR-6 modules:

• Up to six CR-6 modules can be installed on a CH-6 in a BB-6 cabinet

• One or two CR-6 modules can be installed in a BB-2 cabinet

Chassis

The CH-6 chassis is used to mount CR-6 modules in a BB-6 cabinet. It accom-

modates up to six CR-6 modules in a single cabinet row three modules wide

and two modules deep.

WARNING

All relay switch contacts are shipped in the standby state (open) state, but may have transferred to the activated (closed) state during shipping. To ensure that

the switch contacts are in their correct state, modules must be made to communicate with the panel before connecting circuits controlled by the module.

RELAY CONTACT RATINGS:

I56-1798-009

CURRENT RATING MAXIMUM VOLTAGE LOAD DESCRIPTION APPLICATION

2 A 25 VAC PF = 0.35 Non-coded

3 A 30 VDC Resistive Non-coded

2 A 30 VDC Resistive Coded

0.46 A 30 VDC (L/R = 20ms) Non-coded

0.7 A 70.7 VAC PF = 0.35 Non-coded

0.9 A 125 VDC Resistive Non-coded

0.5 A 125 VAC PF = 0.75 Non-coded

0.3 A 125 VAC PF = 0.35 Non-coded

1 2 3 4

Inhaltsverzeichnis

Seite 1 - CR-6 Six Relay Control Module

D500-48-00 1 I56-1798-009INSTALLATION AND MAINTENANCE INSTRUCTIONSBEFORE INSTALLINGThis information is included as a quick reference installation gui

Seite 2 - C0243-00

FIGURE 1: CH-6 CHASSISThe BB-2 cabinet has a built-in chassis that will accommodate one or two CR-6 modules.FIGURE 2: BB-2 CABINET01234567890786543219

Seite 3 - 4˝ (6.35mm) of

FIGURE 6A: INSTALLATION OF CR-6 MODULE IN A REAR CHASSIS POSITION, METHOD TwO1Step 1: Insert the bottom edge of the CR-6 module down into a rear sl

Seite 4 - 5.8"